Posiadam dwa dyski ST3600057SS. Cena za jeden - 300, za dwa 500.

Dyski posiadają przebieg ok 21 godzin, i ok 0.01GB przetworzonych danych - praktycznie jak nowe. Brak błędów Elements in grown defect list: 0
Poniżej więcej informacji diagnostycznch

=== START OF INFORMATION SECTION ===
Vendor: SEAGATE
Product: ST3600057SS
Revision: 0008
Compliance: SPC-3
User Capacity: 60*******66,816 bytes [600 GB]
Logical block size: 512 bytes
Rotation Rate: 15000 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000c5005a6ff8fb
Serial number:
Device type: disk
Transport protocol: SAS (SPL-4)
Local Time is: Sun Jan 26 16:48:20 2025 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature: 41 C
Drive Trip Temperature: 68 C

Elements in grown defect list: 0

Vendor (Seagate Cache) information
Blocks sent to initiator = 2715099
Blocks received from initiator = 72732
Blocks read from cache and sent to initiator = 33079
Number of read and write commands whose size = segment size = 277
Number of read and write commands whose size > segment size = 13

Vendor (Seagate/Hitachi) factory information
number of hours powered up = 20.98
number of minutes until next internal SMART test = 32

Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 303 0 0 303 303 0.054 0
write: 0 0 0 0 0 0.038 0
verify: 11266 0 0 11266 11266 1.336 0

Non-medium error count: 0

[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
No Self-tests have been logged

Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 20:59 [1259 minutes]
Number of background scans performed: 1, scan progress: 3.19%
Number of background medium scans performed: 8
Device does not support General statistics and performance logging

Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: loss of dword synchronization
negotiated logical link rate: phy enabled; 3 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5005a6ff8f9
attached SAS address = 0x5001e676405f2000
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization count = 3120
Phy reset problem count = 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 1.5 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000c5005a6ff8fa
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization count = 0
Phy reset problem count = 0