Hydraulic lift for STRONGER outboard motor

Everything is new with a 1 year warranty, sending by dpd mail, payment to the courier. If you have any questions, write better here on olx, you can in watsap or viber

Electro-hydraulic vertical lift "elevator" for outboard motors - designed to fine-tune the depth of the outboard motor propeller. With this device, you can fully unleash the potential of the engine and achieve maximum speed and fuel economy when using the optimal propeller.

The principle of operation of the elevator is as follows: when the boat moves through the water, you have the opportunity, by adjusting the height of the outboard motor, to achieve the most optimal depth of its propeller, as a result of which the speed performance of the boat improves, as well as significant fuel savings. When using the control panel, you can more precisely adjust the depth of the motor in steps, and then, after detuning, save your preferred position to non-volatile memory, and thus in the future, by pressing just one button, switch to the previously tuned-in marching mode.

Device installation

The product already has all standard mounting holes that are suitable for mounting most outboard motors from 50 horsepower with trim on board. If your motor mounting holes, or the holes already drilled on the boat, do not match those on the elevator, you may need to drill additional mounting holes yourself. Below is a drawing showing the distances between the main mounting holes. Before installing the lift on the boat, make sure your holes on the motor match those already on the lift, or drill new ones.

Device dimensions

Side to boat transom

side to motor

Refer to your outboard motor's installation manual to drill the correct size and location of mounting holes. Fasteners for attaching the hydraulic lift to the boat transom are supplied with the product. Make sure you have separate mounting hardware to further mount the motor to the lift. These fasteners are not supplied with the device. Next, you will need to attach the lift to the boat's transom. To do this, you need to disconnect your outboard motor from the transom if it has already been installed. Then, on the already drilled holes for mounting the motor, install the lift with the help of fasteners and fix it tightly. Please refer to the figure below for how the insulating elements and T-washers supplied with the lift should be installed.

If you are performing the initial installation, then in this case it is advisable for you to contact the specialists and entrust the installation of the device to them. Next, you proceed to connect the hydraulic station, replace the plugs with fittings on the cylinder and connect the station to the cylinder with hydraulic hoses. You can find this process in the instructions for the trim.

Connecting the device to the battery

In order to switch the electrical part of the hydraulic lift, please use the connection diagram shown in the figure below.

Exploitation

To carry out a quick start from the water and exit the boat to the glider, you need to lower the elevator with the motor to the lowest position. Then, after your boat is on the speedboat, you can further adjust the propeller depth by raising the motor up. To find its optimal depth, it is necessary that the boat goes through the water in a gliding mode with a fixed position of the commander. Next, you change the height of the motor and observe the speed of the boat on any speed gauge. You will see in which position your boat began to move faster. This will be the most optimal position for further high-speed and economical driving. The elevator is controlled by a non-fixed three-position toggle switch, or control panel. The control of the toggle switch allows you to raise and lower the elevator to the extreme positions, as well as to make manual adjustments by briefly pressing up or down. This option is basic, and the adjustment of the position of the motor will occur anew each time. If you want more precise control with the ability to remember your favorite position in this case, you will need to additionally purchase a panel and an elevator control unit. Using the control panel, you will be able to raise and lower the elevator to the extreme upper and lower positions. You will have the possibility of precise step-by-step adjustment by briefly pressing the keys up or down with a step of 2 cm movement of the elevator in both directions. You will also be able to memorize your favorite position in which your boat will have the highest efficiency. To do this, you will need to enter the data into a non-volatile memory by pressing the M key on the device control panel.
memory. And in the future, after the boat enters the glider, you will only need to press one key M and the elevator itself will become in a position predetermined by you.

CHARACTERISTICS
Dimensions of the device when folded
Length 440 mm, width 372 mm, height 114 mm
Dimensions of the device in the unfolded state
Length 455 mm, width 372 mm, height 114 mm
Weight of the device with hydraulic station
16.5 kg
Unit weight without hydraulic station
13 kg
Voltage
12 V
Lifting height of the device
120 mm
Device for motor power
from 50 hp up to 150 hp
Maximum boat motor weight
Not more than 220 kg
Material
Stainless steel
Protection against galvanic corrosion
Yes
Hydraulic lift power
1000 kg