Prywatne
Stan: Używane
Opis
Witam,
do sprzedania mocna końcówka mocy 200W Dynaco i przedwzmacniacz lampowy z tej samej serii z lat 70tych
Idealne rozwiązanie gdy potrzeba mocy a chcemy analogowego, lampowego brzemienia. Przez ostatnie kilka lat to był mój sprzęt referencyjny. Stan techniczny absolutnie idealny. Stan wizualny bardzo dobry. Wszystko pięknie działa i gra. Świetny sprzęt.
Dodatkowo przedwzmacniacz wyposażony w pre gramofonowe wysokiej klasy.
Mam do nich instrukcje i manuale.
Zapraszam do kupna
PAS 4 Specifications
Phono Section
GAIN:
40 dB
RIAA ACCURACY:
+/- .5 dB from 20 Hz to 20 kHz 500mV RMS 1kHz
PHONO OVERLOAD:
500mV RMS 1kHz
MAXIMUM OUTPUT CAPABILITY:
60V RMS 1kHz
THD:
50V RMS 20kHz (for 1% THD)
less than .025% 2V RMS Output
INPUT IMPEDANCE:
47k shunted by 10pF
TAPE OUTPUT IMPEDANCE:
2k
NOISE:
-86 dB below 10mV RMS Input
ABSOLUTE PHASE:
Non-Inverting
TUBE COMPLEMENT:
2ea 6DJ8 (6922); 2ea 12AX7 (ECC83)
Line Section
GAIN:
8.5 dB
FREQUENCY RESPONSE:
2 Hz to 150 kHz (nominal)
(-3 dB, 20 k ohm load)
MAXIMUM OUTPUT:
40V RMS (for 1% THD)
THD:
.025% 2V RMS Output
INPUT IMPEDANCE:
25k nominal (all inputs)
OUTPUT IMPEDANCE:
40 ohms
NOISE:
-90 dB below 2V RMS Output
ABSOLUTE PHASE:
Inverting
SLEW RATE:
40 V/μs
TUBE COMPLEMENT:
2ea 6DJ8 (6922)
Electrical / Mechanical
POWER REQUIREMENTS:
100, 115, or 230 VAC 50/60 Hz
POWER CONSUMPTION:
45 Watts
DIMENSIONS:
17" Wide, 3.75" High, 12" Deep
WEIGHT
13 lbs
DYNACO STEREO 400 Series 2
When DYNACO introduced the original series 400 during the “power wars" of the early 1970s, it was soon recognized as a breakthrough in audio technology and went on to become the best-selling high-power amplifier of the 70’s – perhaps of all time. Tens of thousands of original STEREO 400’s are still satisfying listeners around the globe, proof of DYNACO’s reliability.
Then DYNACO introduced the STEREO 400 series 2, featuring 200 Watts of state-of-the-art amplification per channel and the uncanny ability to reproduce music with stunning realism. Like the PAS-4, it was 100% conceived, engineered and manufactured in the USA. The redesigned STEREO 400 Series 2 set a new standard for great performance at a reasonable price.
STEREO 400 Series 2 easily outperformed all other amplifiers in its price range and challenged amplifiers costing two or three times more. In addition, DYNACO engineers created a new feature for the STEREO 400 Series 2 not found on any other amplifier. A switch on the front panel lets you select between "Normal Current" for easy to drive 8 ohm loads and "High Current" for more difficult low impedance speakers. Based upon where the speaker and RCA input terminals are located, I suspect it is a Dual-Mono design.
DIMENSIONS
17” Wide, 3.75” High, 12” Deep
WEIGHT
25 lbs
do sprzedania mocna końcówka mocy 200W Dynaco i przedwzmacniacz lampowy z tej samej serii z lat 70tych
Idealne rozwiązanie gdy potrzeba mocy a chcemy analogowego, lampowego brzemienia. Przez ostatnie kilka lat to był mój sprzęt referencyjny. Stan techniczny absolutnie idealny. Stan wizualny bardzo dobry. Wszystko pięknie działa i gra. Świetny sprzęt.
Dodatkowo przedwzmacniacz wyposażony w pre gramofonowe wysokiej klasy.
Mam do nich instrukcje i manuale.
Zapraszam do kupna
PAS 4 Specifications
Phono Section
GAIN:
40 dB
RIAA ACCURACY:
+/- .5 dB from 20 Hz to 20 kHz 500mV RMS 1kHz
PHONO OVERLOAD:
500mV RMS 1kHz
MAXIMUM OUTPUT CAPABILITY:
60V RMS 1kHz
THD:
50V RMS 20kHz (for 1% THD)
less than .025% 2V RMS Output
INPUT IMPEDANCE:
47k shunted by 10pF
TAPE OUTPUT IMPEDANCE:
2k
NOISE:
-86 dB below 10mV RMS Input
ABSOLUTE PHASE:
Non-Inverting
TUBE COMPLEMENT:
2ea 6DJ8 (6922); 2ea 12AX7 (ECC83)
Line Section
GAIN:
8.5 dB
FREQUENCY RESPONSE:
2 Hz to 150 kHz (nominal)
(-3 dB, 20 k ohm load)
MAXIMUM OUTPUT:
40V RMS (for 1% THD)
THD:
.025% 2V RMS Output
INPUT IMPEDANCE:
25k nominal (all inputs)
OUTPUT IMPEDANCE:
40 ohms
NOISE:
-90 dB below 2V RMS Output
ABSOLUTE PHASE:
Inverting
SLEW RATE:
40 V/μs
TUBE COMPLEMENT:
2ea 6DJ8 (6922)
Electrical / Mechanical
POWER REQUIREMENTS:
100, 115, or 230 VAC 50/60 Hz
POWER CONSUMPTION:
45 Watts
DIMENSIONS:
17" Wide, 3.75" High, 12" Deep
WEIGHT
13 lbs
DYNACO STEREO 400 Series 2
When DYNACO introduced the original series 400 during the “power wars" of the early 1970s, it was soon recognized as a breakthrough in audio technology and went on to become the best-selling high-power amplifier of the 70’s – perhaps of all time. Tens of thousands of original STEREO 400’s are still satisfying listeners around the globe, proof of DYNACO’s reliability.
Then DYNACO introduced the STEREO 400 series 2, featuring 200 Watts of state-of-the-art amplification per channel and the uncanny ability to reproduce music with stunning realism. Like the PAS-4, it was 100% conceived, engineered and manufactured in the USA. The redesigned STEREO 400 Series 2 set a new standard for great performance at a reasonable price.
STEREO 400 Series 2 easily outperformed all other amplifiers in its price range and challenged amplifiers costing two or three times more. In addition, DYNACO engineers created a new feature for the STEREO 400 Series 2 not found on any other amplifier. A switch on the front panel lets you select between "Normal Current" for easy to drive 8 ohm loads and "High Current" for more difficult low impedance speakers. Based upon where the speaker and RCA input terminals are located, I suspect it is a Dual-Mono design.
DIMENSIONS
17” Wide, 3.75” High, 12” Deep
WEIGHT
25 lbs
ID: 746574870
xxx xxx xxx
Dodane 20 maja 2024
Dynaco 400 Serie II i Dynaco PAS-4 końcówka i przedwzmacniacz lampowy
9 900 zł
Użytkownik
Lokalizacja